Mtd 31AE633E401 Manuel d'utilisateur télécharger pdf (Page 10)

Chute Tilt Control

The distance snow is thrown can be adjusted by

adjusting the angle of the chute assembly. Move the

chute tilt control forward to decrease the distance, and

towards the rear to increase the distance.

Discharge Chute

The angle of the discharge chute controls the distance

that the snow is thrown. Tilt the discharge chute up for

greater distance; tilt down for less distance.

Fuel Shut-off Valve (If equipped)

If your snow thrower is equipped with a fuel shut-off

valve, locate it under the fuel tank. This valve controls

fuel flow from the tank. Always make certain it is in the

open (vertical) position before attempting to start the

engine. See Figure 13.

Headlight

The headlight is on whenever the engine is running.

Throttle Control

The throttle control is located on the engine. It regulates

the speed of the engine.

Safety Ignition Key

The safety ignition key must be fully inserted in the

switch before the unit will start. Remove key when snow

thrower is not in use. Do not attempt to turn the key.

Skid Shoe

The position of the skid shoe is determined by the

condition of the ground from where snow has to be

removed. Refer to page 8 for details.

SECTION 4: OPERATING YOUR SNOW THROWER

Before Starting

WARNING: Read, understand, and follow

all instructions and warnings on the machine

and in this manual before operating.

• The spark plug wire was disconnected for safety.

Attach spark plug wire to spark plug before starting.

Gas and Oil Fill-Up

• Check oil and gasoline level and add if necessary.

Follow related instructions in the seperate engine

manual packed with your snow thrower.

WARNING: Use extreme care when

handling gasoline. Gasoline is extremely

flammable and the vapors are explosive.

Never fuel the machine indoors or while the

engine is hot or running. Extinguish cigarettes,

cigars, pipes and other sources of ignition.

To Start Engine

• Make certain the fuel cut-off valve, if your snow

thrower is so equipped, is in OPEN position.

• Make certain the auger and drive clutch levers are

in the disengaged (released) position.

• Move throttle control up to FAST position. Insert

ignition key into slot. Make sure it snaps into place.

Do not turn key

NOTE: Engine will not start unless ignition key is

inserted into ignition slot in carburetor cover.

Electric Starter

WARNING: The electric starter is equipped

with a grounded three-wire power cord and

plug, and is designed to operate on 120 volt

AC household current. It must be used with a

properly grounded three-prong receptacle at

all times to avoid the possibility of electric

shock. Follow all instructions carefully prior to

operating the electric starter.

• Determine that your house wiring is a three-wire

grounded system. Ask a licensed electrician if you

are not certain.

• If your house wiring system is not a three-wire

grounded system, do not use this electric starter

under any conditions.

• If your home electrical system is grounded, but

a three-hole receptacle is not available, one should

be installed by a licensed electrician before using

the electric starter.

• If you have a grounded three-prong receptacle,

proceed as follows.

• Rotate choke knob to OFF position.

• Connect power cord to switch box on engine. Plug

the other end of power cord into a three-prong 120-

volt, grounded, AC receptacle.

• Push starter button to crank engine. As you crank

the engine, move choke knob to FULL choke

position.

• When engine starts, release starter button, and

move choke gradually to OFF. If engine falters,

move choke immediately to FULL and then

gradually to OFF.

1 2 ... 5 6 7 8 9 10 11 12 13 14 15 ... 27 28

Commentaires sur ces manuels

Pas de commentaire

Mtd 31AE633E401 Manuel d'utilisateur Page 10

Commentaires sur ces manuels

Produits connexes et manuels pour Voitures Mtd 31AE633E401