$1.00owners GUIDEOUTDOOR POWER EQUIPMENT for all seasonsIMPORTANT:Read Safety Rules and Instructions CarefullyREAR TINE TILLERSModel Numbers 218-40
HANDLE ADJUSTMENT (Model 405)The handle may be placed in one of nine differen positions. The handle may be adjusted to one of three height p
Wheels—Lubricate the wheel bearings with a light oil after each fifteen hours of operation.Wheel Drive—The wheels are driven by pawl and ratche
Tine (Long) Belt Removal1. Remove belt cover by removing the four selftapping screws. See figure 21.Belt CoverFIGURE 21.2. Lift the belt from under
Remove the belt and install the new belt. Be sure the belt is routed around the guide pins as shown in figure 26. ^NOTEBelt must be between the “
TROUBLE SHOOTING CHARTSYMPTOMPOSSIBLE CAUSE(S)SOLUTIONEngine fails to start1. Check fuel lank for gas.2. Spark plug ead wire disconnectef.3. Faulty
NOTES15
Models 402, 404 and 405 I^NOTEThis manual covers various models and all specifications shovi/n do not necessarily apply to your model. Specific
Models 402, 404 and 405PARTS LIST FOR MODELS 402, 404 AND 405 ROTARY TILLERSREF.NO.PARTNO.COLORCODEDESCRIPTIONNEWPARTREF.NO.PARTNO.COLORCODEDESCRIPTIO
Models 402, 404 and 4059/NOTE: The engine is not under warranty by the mower manufacturer.. .if repairs or service is needed on the engine, please con
Models 402, 404 and 405PARTS LIST FOR MODELS 402, 404 AND 405 ROTARY TILLERSREF.NO.PARTNO.COLORCODEDESCRIPTIONNEWPARTREF.NO.PARTNO.COLORCODEDESCRIPTIO
INDEXSafe Operation Practices...3Assembiy...4Con
Models 402, 404 and 405TINE CHAIN CASE 14981TILLER CHAIN CASE 14981 (TINES)REF.NO.PARTNO.COLORCODEDESCRIPTIONNEWPARTREF.NO.PARTNO.COLORCODEDESCRIPTION
Models 402, 404 and 405WHEEL CHAIN CASE 14963 (404 and 405)REF.NO.PARTNO.COLORCODEDESCRIPTIONNEWPARTREF.NO.PARTNO.COLORCODEDESCRIPTIONNEWPART1 14962
Heavy Duty Rear Tine Garden Tiller Attachments Availabi 3 for All-Season Use31-011031-014431-01458" Fui “V”-B with “V” Tine Wh€ Depth usee Incli
PARTS INFORMATIONPOWER EQUIPMENT PARTS AND SERVICEParts and service are available through the authorized service firm; listed below. All orders should
^ *waVn*nV^JTo reduce the potential for any injury, comply with the following safety instructions. Failure to comply with the instructions may r
«ASSEMBLYo----FIGURE 1.FIGURE 2./NOTEThis unit is shipped WITHOUT GASOLINE or OIL. After assembly, see separate engine manual for prope
2. Insert clevis pin (D) through the tine shield and depth bar assemblies. Secure with hairpin cotter—(E). See figure 4.3. Insert hex bolt (A) into
Belleville Washers (3)FIGURE 7—Model 405 Shown.FIGURE 8.FIGURE 9.2. Place handle assembly in position on the tiller. Working on one side of the unit
Control WireHole in Clutch LeverFIGURE 10.1. Remove one nut and the lock washer from the end of the drive clutch cable (short cable). Slip th
OPERATIONNOTEEngine is shipped without oil.BEFORE STARTING1. Before operating tiller for the first time or if tines have been removed and reassem
Ai WAFWARNING IDo not push down on the handles so that the wheels are lifted off the ground while the tine ciutch is engaged, or the tiil
Commentaires sur ces manuels