MTD 2P5 Spécifications

Safe Operation Practices • Set-Up • Operation • Maintenance • Service • Troubleshooting • WarrantyLSingle=Stage Snow Thrower m Mocleis 2N1 & 2P5MT

Controlsand Features4AugChute ControlChuteAssemblyAugerPrimerThrottleControlChokeControlOU DrainGasolineElectricFigure 4=1NOTE:This Operator's Ma

AugerWhen engaged, the auger rotation draws snow into the augerhousing and throws it out the discharge chute. Rubber paddleson the auger also aid in p

OperationStarting the Enginel_lhllL ARNING! Always keep hands and feet clear ofmoving parts. Do not use a pressurized startingfluid. Vapors are flamma

RecoilStarterCAUTION! Do not pull the starter handle while theengine is running.WARNING: To avoid unsupervised engineoperation, never leave the engine

Maintenance& AdjustmentsAdjustmentsWARNING! Before Servicing, repairing orinspecting the snow thrower, disengage the augercontrol. Stop the engine

MaintenanceLubricationLubricate the pivot points on the control handle and theextension spring at the end of the control cable with a lightoil once ev

EngineMaintenance7_ ARNING! To prevent accidental start-up, shut offthe engine and remove the key before performingany type of engine maintenance.Main

Changing EngineOilNOTE: Check the oil level before each use and after every fivehours of operation to be sure the correct oil level is maintained.Refe

5. After the spark plug is seated, tighten with a spark plugwrench to compress the washer.NOTE:When installing a new spark plug, tighten 1/2-turnafter

ServiceReplacingBelt1. Remove the belt cover by removing the five hex screwsthat secure it to the frame. See Fig. 8-1.Hex ScrewsFigure 8-12. Remove th

ToTheOwner1ThankYouThank you for purchasing a Snow Thrower manufactured byMTD LLC. It was carefully engineered to provide excellentperformance when pr

Troubleshooting9ProblemEngine Fails to startEngine running erratically/inconsistent RPM (huntingor surging)Engine overheatsLoss of powerExcessive vibr

ReplacementParts1Component l Part Number and Descriptionj///731-1033 Shave Plate954-04204 Belt V-Type735-04032735-04033753-04472Spiral CrescentRubber

MTD CONSUMER GROUP INC (MTD), the California Air Resources Board (CARB)and the United States Environment Protection Agency (U. S. EPA)Emission Control

(4)Repairorreplacementofanywarrantedpartunderthewarrantyprovisionsofthisarticlemustbeperformedatnochargetotheowneratawarrantystation.(5)Notwithstandin

MANUFACTURER'S LiMiTED WARRANTY FORThe limited warranty set forth below is given by MTD LLC withrespect to new merchandise purchased and used in

ImportantSafeOperationPractices2WARNING! This symbol points out important safety instructions which, if not followed,could endanger the personal safet

SafeHandling of GasolineTo avoid personal injury or property damage use extreme carein handling gasoline. Gasoline is extremely flammable and thevapor

Clearinga CloggedDischargeChuteHand contact with the rotating impeller inside the dischargechute is the most common cause of injury associated with sn

Safety SymbolsThis page depicts and describes safety symbols that may appear on this product. Read, understand, and follow all instructions on themach

Assembly& Set-Up3Contentsof CartonTwo Ignition KeysOne 20 oz. Bottle 5W-30 OilOne Snow Thrower Operator'sManualNOTE:This Operator's Manu

Adding Fuel1.2.WARNING! Use extreme care when handlinggasoline. Gasoline is extremely flammable and thevapors are explosive. Never fuel the machineind

AdjustmentsChuteAssemblyThe pitch of the chute assembly controls the angle at which thesnow isthrown.1. Loosen the wing knob found on the left side of