MTD 24620L Instructions d'exploitation télécharger pdf (Page 10)

Operating Instructions English

Installing and configuring the

gear select lever

Figures 5, 7 and 8

‚" Detach the screws and nuts (O)

and remove the mounting plate

(N).

‚" Remove the plastic grip (B)

from the lever (I).

‚" Press the nylon sleeve (Z) into

the control panel (L) from

below.

‚" Push the unit (J = washer,

spring, washer) on the lever (I).

‚" Now guide the lever (I) through

the sleeve (Z), and make sure

that the pin (K) is engaged in the

bottom recess Figure 7.

‚" Now use the screws and nuts (O)

to reattach firmly the mounting

plate (N), including the rod (I),

to the bracket (M) as shown in

Figure 8. Make sure that the

mounting plate (N) is under the

bracket (M).

‚" Push the plastic grip (B) over the

lever (I).

‚" Turn the lever (I) clockwise until

the pin (K) engages in the

neutral position (at the right side

of the bottom recess) as shown

in Figure 7.

‚" If necessary, move the shift arm

(X in Figure 8) from side to side

at every shift stage until the

gears engage in neutral.

Note: When the shift arm (X) is

moved to the far left, and then to the

far right a notch down, neutral

should be engaged.

At neutral the

appliance must offer no resistance at

all when the user presses the safety

lever (W in Figure 5) to push it over

the floor.

‚" Once the shift lever (X) is at

neutral, it may become necessary

to screw in or out the connector

(P) until it lies flush with the

hole in the rod (I).

Note: Make sure that the pin (K) is

still at the neutral position.

‚" Now guide the bent end of the

connector (P) through the hole in

the rod (I), and secure this with

the split pin (Q).

‚" Press the lever (W) for the safety

lock, and move the appliance

backwards and forwards.

The wheels should turn without

resistance. Should this not be the

case, the length of the connector

(P) must be readjusted.

Checking the braking system

Move the gearshift lever to the

neutral position (N). Let go of all

control levers, and try to move the

appliance back and forth. The wheels

should not turn. Should they turn, the

braking system must be configured.

Do not use the appliance, and please

contact a specialist garage that can

configure the appliance.

Connecting the cable rod

to the ignition

(appliances with electric

starter)

At the free end of the cable rod there

are four cables attached to a large

plastic plug and two to a small one.

Connect the large plug to the base

of the ignition lock located on the

control panel.

Use two cable ties to secure the cable

rod to the right stem at a safe

distance from the rotating parts.

Operating safety

Also observe the information in the

operating instructions for the

engine.

Danger/accident!

All persons, and especially children,

and animals must not come near the

appliance when it is mowing. There

is a risk of injury from stones and

similar flung out of the appliance.

Children must not operate the

appliance.

Before reversing, you must check the

area behind the appliance and switch

OFF the cutters.

Falls

Operate the vehicle at walking speed

only.

Be particularly careful when mowing

in reverse and pulling the appliance

towards you.

Mowing on steep inclines can cause

the appliance to tip, and you can

become injured. Steer the appliance

directly across inclines, and never up

and down them.

Be particularly careful when

changing direction. Do not mow on

inclines greater than 15°.

Mowing along perimeters involves

a risk of injury. Mowing near edges,

hedges, or steep inclines is

dangerous. Keep a safe distance

from perimeters when mowing.

Mowing on damp grass can reduce

the appliance’s wheel grip, and you

can fall. Mow only when the grass

is dry.

Work only by daylight or in good

artificial lighting.

Injury

The safety distance between the

guide stems and the rotary cutters

must be maintained at all times.

Before manoeuvring the appliance

over footpaths, access roads,

or similar, stop the engine.

Check the surface on which the

appliance is to be used and remove

all objects that the appliance can

take up and fling out.

Should a foreign body, e.g. a stone,

hit the cutters or the appliance begin

to vibrate with unusual violence:

stop the engine immediately.

Check the appliance for damage,

and have any damage repaired at

a specialised garage.

There must be nothing placed in

front of the grass ejector of a rotary

lawnmower.

Asphyxiation.

Risk of asphyxiation from carbon

monoxide. Let the IC engine run

only in well-ventilated rooms and

outdoors.

Explosion and fire hazard.

Petrol vapours are explosive,

and petrol is highly flammable.

Fill the engine with fuel before

starting it. Keep the fuel tank closed

when the engine is running or still

hot.

1 2 ... 5 6 7 8 9 10 11 12 13 14 15 16 17

Commentaires sur ces manuels

Pas de commentaire

MTD 24620L Instructions d'exploitation Page 10

Commentaires sur ces manuels

Produits connexes et manuels pour Edgers MTD 24620L