MTD SNOW THROWER Manuel de l'opérateur Page 1

MTD LLC, P.O. BOX 361131 CLEVELAND, OHIO 44136-0019Printed In USASafe Operation Practices • Set-Up • Operation • Maintenance • Service • Troubleshoot

Ignition KeyOil FillPrimerGasolineCapElectricStarterOutletRecoilStarterOil DrainChokeControlThrottleControlElectricStarterButtonAuger ControlRecoil St

AugerWhen engaged, the augers rotation draws snow into the auger housing and throws it out the discharge chute. Rubber paddles on the augers also aid

Starting the EngineWARNING! Always keep hands and feet clear of moving parts. Do not use a pressurized starting fluid. Vapors are flammable.NOTE: Allo

Recoil StarterCAUTION! Do not pull the starter handle while the engine running. WARNING: To avoid unsupervised engine operation, never leave the engi

AdjustmentsWARNING! Before Servicing, repairing or inspecting the snow thrower, disengage the auger control. Stop the engine and remove the key to pre

Maintenance ScheduleTasksFirst 5 Hrs.Each Use or Every 5 Hrs.Every Season or 25 Hrs.Every Season or 50 Hrs.Every Season or 100 Hrs.Service DatesCheck

Changing Engine OilNOTE: Check the oil level before each use and after every five hours of operation to be sure the correct oil level is maintained.

After the spark plug is seated, tighten with a spark plug 5. wrench to compress the washer.NOTE: When installing a new spark plug, tighten ⁄-turn af

Replacing BeltRemove the belt cover by removing the five hex screws 1. that secure it to the frame. See Fig. 7-1. Remove the belt by grasping it from

Replacing Auger PaddlesThe snow thrower auger’s rubber paddles are subject to wear and should be replaced if any signs of excessive wear are present.C

To The Owner12Record Product InformationBefore setting up and operating your new equipment, please locate the model plate on the equipment and record

Problem Cause RemedyEngine Fails to start Fuel tank empty, or stale fuel.1. Blocked fuel line.2. Key not inserted all the way.3. Spark plug wire disco

Component Part Number and Description731-1033 Shave Plate 754-04204 Belt V-Type735-04032 Spiral Crescent735-04033 Rubber Paddle753-04472 Rep

MTD CONSUMER GROUP (MTD) and the United States Environment Protection Agency (U. S. EPA) Emission Control System Warranty Statement (Owner’s Defect Wa

(7) The engine manufacturer is liable for damages to other engine components proximately caused by a failure under warranty of any warranted part.

MANUFACTURER’S LIMITED WARRANTY FORGDOC-100016 REV. BThe limited warranty set forth below is given by MTD LLC with respect to new merchandise purchase

Important Safe Operation Practices23TrainingRead, understand, and follow all instructions on the 1. machine and in the manual(s) before attempting to

4 se c t i O n 2 — iM p O r t a n t sa f e Op e r a t i O n pr a c t i c e sSafe Handling of GasolineTo avoid personal injury or property damage u

5se c t i O n 2 — iM p O r t a n t sa f e Op e r a t i O n pr a c t i c e sMaintenance & StorageNever tamper with safety devices. Check their

6 se c t i O n 2 — iM p O r t a n t sa f e Op e r a t i O n pr a c t i c e sSafety SymbolsThis page depicts and describes safety symbols that may

Contents of CartonTwo Ignition Keys• One 20 oz. Bottle 5W-30 Oil• One Snow Thrower Operator’s • ManualNOTE: This Operator’s Manual covers several mo

Adding FuelWARNING! Use extreme care when handling gasoline. Gasoline is extremely flammable and the vapors are explosive. Never fuel the machine indo

AdjustmentsChute AssemblyThe pitch of the chute assembly controls the angle at which the snow is thrown.Loosen the wing knob found on the left side of