MTD 400 Manuel de service télécharger pdf (Page 25)

OPERATING CHARACTERISTICS

I A

Temperature control

Control is performed based on the system water return tem-

perature.

The set points refer to the water return temperature.

The water outlet temperature depends on the difference

between inlet and outlet, usually 5°C (rated).

This temperature difference may change depending on the

type of water circuit.

For example, if the HEAT set point is set to +30°C, the outlet

temperature will be +35°C.

The return temperature is also used to activate the

resources inside or outside unit (e.g. electric heaters).

The controller features Full Floating technology that optimis-

es, when the scan time elapses, the water temperature set

points (COOL/HEAT/DHW) in relation to the compressor

operating time and the water temperature.

To display the actual set point, select directory Sr and the

active operating mode (Cool, Heat, DHW), as described in

the paragraph "Displaying installer parameters ".

Cooling set point

(factory setting) = 12°C, Hysteresis = 3°C.

The compressor starts at outlet water temperatures above

12°C+3°C (15°C).

The compressor stops at water temperatures below 12°C.

Heating set point

(factory setting) = 40°C, Hysteresis = 3°C.

The compressor starts at outlet water temperatures below

37°C.

The compressor stops at water temperatures above 40°C.

In the event of temporary power failure, when power returns,

the mode set previously will be retained in the memory.

COMPRESSOR START UP DELAY

Two functions prevent the compressor from starting up too

frequently:

- Minimum time since last shut-down 3 minutes.

- Minimum time since last start-up 5 minutes.

CIRCULATING PUMP

The electronic board has an output for managing the circu-

lating pump, always on in COOL and HEAT modes, and off

with a 1 minute delay when unit shuts down (standby).

After the first minute of pump operation when the water flow

is at full speed, the water flow alarm functions are activated

(differential pressure switch and flow switch).

FAN SPEED CONTROL

To enable the unit to function correctly at different outside

temperatures, a microprocessor with pressure reading via

temperature sensor controls the fan rotation speed. This

allows the exchange of heat to be increased and/or

decreased, maintaining condensing or evaporation pres-

sures essentially constant. The fan operates independently

of the compressor.

FROST ALARM

The frost protection function is always active even if the con-

troller is standby.

To prevent the water freezing and damaging the plate heat

exchanger, the microprocessor shuts down the compressor

if the temperature measured by the heat exchanger outlet

temperature sensor is less than +4°C.

The frost prevention temperature set point can be modified

by an authorised service centre only and only after verifying

that the water circuit contains antifreeze.

Tripping of this alarm shuts down the compressor but not

the pump, which remains active.

To reset normal functions, the water outlet temperature must

rise to more than +7°C. Reset is automatic.

If the frost alarm is tripped more than 3 times in one hour,

reset becomes manual.

DOMESTIC HOT WATER FROST PROTECTION

The domestic hot water frost protection function is only

active if an auxiliary resource is installed for the domestic

hot water storage (parameter CL61=28).

The auxiliary resource is activated if the water temperature,

measured by sensor BT4, is less than +5°C, and is deacti-

vated at +7°C.

FROST PROTECTION WITH UNIT IN STANDBY

Version AWR MTD (complete with built-in heaters)

The frost protection function is guaranteed by the activation

of the heating element inside the unit and the start of the

system pump.

The pump and the first stage of the electric heater (see Tab.

1) are activated if the water temperature (measured by sen-

sor BT2 at the heat exchanger outlet) is less than 4.5°C,

and are deactivated when the water temperature reaches

+7°C.

Version AWR MTD/B

The frost protection function is guaranteed by the activation

of the 200W electric heater used to protect the heat

exchanger, and by the activation of the system pump.

The pump and the electric heater are activated if the water

temperature (measured by sensor BT2 at the heat exchang-

er outlet) is less than 4.5°C, and are deactivated when the

water temperature reaches +7°C.

WATER FLOW ALARM

The microprocessor manages a water flow alarm controlled

by a differential pressure switch installed as standard on the

unit, and a flow switch to be installed on the water outlet pip-

ing.

This safety device may trip after the first 60 seconds of

pump operation, if the water flow-rate is not sufficient.

The alarm shuts down the compressor and not the pump,

which remains active if the alarm lasts less than 20 sec-

onds, otherwise the unit is shut down completely.

DYNAMIC DEFROST

The unit manages the defrosts by reversing the refrigerating

cycle, switching the position of the reversing valve and oper-

ating the circuit in cooling mode for a few minutes with the

fans off.

The defrost cycle removes the ice that forms on the surface

of the outdoor heat exchanger external at low temperature

and high humidity.

The unit controller features smart defrost management in

relation to the temperature read by the outside air tempera-

ture sensor and the pressure in the refrigerant circuit.

The graph of the function is shown below.

25GB 01/2009 AWR MTD - AWR MTD/B

1 2 ... 20 21 22 23 24 25 26 27 28 29 30 ... 51 52

Commentaires sur ces manuels

Pas de commentaire

MTD 400 Manuel de service Page 25

Commentaires sur ces manuels

Produits connexes et manuels pour Mini-faucheuses MTD 400