IMPORTANT: READ SAFETY RULES AND INSTRUCTIONS CAREFULLYMTD PRODUCTS INC. P.O. BOX 368022 CLEVELAND, OHIO 44136-9722Model NumbersE642E, E662H,614E, E64
104. Place one flat washer on the end of the chutecrank, then insert the end of the crank into thehole in the plastic bushing in the chute crankbrac
11 Adjusting The Skid Shoes The space between the shave plate and the groundcan be adjusted by adjusting the skid shoes. 1. Place skid shoes in the
12Figure 22 Figure 23 SECTION 7: OPERATIONBEFORE STARTINGWARNING: Observe all WarningLabels on the snow thrower prior touse. See Figure 1.Your sno
13Follow all instructions carefully. Determine that yourhouse wiring is a three wire grounded system. Ask alicensed electrician if you are not certai
14TO ENGAGE DRIVE/AUGER1. With the engine running near top speed, moveshift lever into one of the FORWARD orREVERSE positions. Select a speedappropri
155. If adjustment is necessary, loosen the jam nuton the traction drive cable, and thread cable inor out as necessary. 6. Tighten the jam nut to sec
16SECTION 9: LUBRICATIONWARNING: Disconnect the sparkplug wire and ground against theengine before performing anylubrication or maintenance.ENGINERe
17AUGER BELTSNOTE: It is necessary to remove both belts inorder to change either one. If changing just one belt,be certain to check the condition of
18Figure 32 CHANGING THE FRICTION WHEEL RUBBERThe rubber on the friction wheel is subject to wearand should be checked after 25 hours of operation,a
19SECTION 12: TROUBLE SHOOTING GUIDENote: For repairs beyond the minor adjustments above, contact your local authorized service dealer.Trouble Possi
2 SECTION 1: IMPORTANT SAFE OPERATION PRACTICES WARNING: THIS SYMBOL POINTS OUT IMPORTANT SAFETY INSTRUCTIONS WHICH, IFNOT FOLLOWED, COULD ENDANGE
20SECTION 13: ILLUSTRATED PARTSHOUSING ASSEMBLY
21 HOUSING ASSEMBLYREF.NO.PARTNO. DESCRIPTION QTY.1 618-0123 Housing—L.H. 12 618-0124 Housing—R.H. 13 710-0642 Screw 54 711-0908 Spiral Axle 24&qu
22HANDLE ASSEMBLY
23HANDLE ASSEMBLYREF.NO.PARTNO. DESCRIPTION QTY.1A 684-0105 Control Panel Ass’y - Top Shift † 11B 684-0106 Control Panel Ass’y.-Front Shift †† 12 6
24FRAME ASSEMBLY
25FRAME ASSEMBLYWheel AssemblyREF.NO.PARTNO. DESCRIPTION QTY.REF.NO.PARTNO. DESCRIPTION QTY.1 618-0063 Bearing Ass’y. 1 25 736-0242 Washer, Bell 12
26REF.NO.PARTNO. DESCRIPTION QTY.1 05896A Bracket-Idler 12 629-0071 Cord-Extension 110V † 13 710-0627 Screw-Hex 14 710-1245 Screw-Hex 15 710-0230 Sc
27Models E642E,E644E,E662H, E664FENGINE AND “V” BELTREF.NO.PARTNO. DESCRIPTION QTY.1 05896A Bracket 12 629-0071 Cord, Extension 13 710-0627 Screw 14
MANUFACTURER’S LIMITED WARRANTY FOR:For TWO YEARS from the date of retail purchasewithin the United States of America, its possessionsand territories,
3 • If the snow thrower should start to vibrateabnormally, stop the engine and checkimmediately for the cause. Vibration is generally awarning of tr
4 SECTION 2: FINDING YOUR MODEL NUMBER This Operator’s Manual is an important part of your new snow thrower. It will help you assemble, prepareand
5 SECTION 4: CONTENTS OF HARDWARE PACK A ATTACHING THE HANDLE ASSEMBLY Lay out the hardware according to the illustration for identification purpos
6 SECTION 5: ASSEMBLY INSTRUCTIONS IMPORTANT: After assembly, service enginewith gasoline, and check oil level as instructed in theseparate engine
73. Insert curved end of the Z fitting into the tophole in the triangular metal tab on the augercontrol grip. See Figure 5.Figure 5 4. Place the au
8Figure 9 Figure 10 ATTACHING SHIFT ROD (Hardware D)1. Place the shift lever in the fifth (5) or the fastestforward speed position.2. Models 642,
9 ATTACHING CLUTCH CABLES 1. Thread the hex jam nuts all the way up thethreaded portion of the “Z” ends.2. Make certain all cables are in the groov
Commentaires sur ces manuels