Mtd Y26SS Manuel d'utilisateur télécharger pdf (Page 3)

RULES FOR SAFE OPERATION

SYMBOL MEANING

• ON/OFF STOP CONTROL

ON / START / RUN

• WARNING - READ OPERATOR'S MANUAL

Read the operator’s manual(s) and follow all warnings

and safety instructions. Failure to do so can result in

serious injury to the operator and/or bystanders.

SAFETY AND INTERNATIONAL SYMBOLS

This operator's manual describes safety and international symbols and pictographs that may appear on this product. Read the

operator's manual for complete safety, assembly, operating and maintenance and repair information.

• ON/OFF STOP CONTROL

OFF or STOP

SYMBOL MEANING

• SAFETY ALERT SYMBOL

Indicates danger, warning or caution. May be used

in conjunction with other symbols or pictographs.

• WEAR EYE AND HEARING PROTECTION

WARNING: Thrown objects and loud noise can

cause severe eye injury and hearing loss. Wear eye

protection meeting ANSI Z87.1 standards and ear

protection when operating this unit. Use a full face

shield when needed.

• KEEP BYSTANDERS AWAY

WARNING: Keep all bystanders, especially

children and pets, at least 50 feet (15 m) from the

operating area.

• THROWN OBJECTS AND ROTATING CUTTER

CAN CAUSE SEVERE INJURY

WARNING: Do not operate without the cutting

attachment shield in place. Keep away from the

rotating cutting attachment.

• HOT SURFACE WARNING

Do not touch a hot muffler, gear housing or cylinder.

You may get burned. These parts get extremely hot

from operation. They remain hot for a short time after

the unit is turned off.

• UNLEADED FUEL

Always use clean, fresh unleaded fuel

• OIL

Refer to operator’s manual for the proper type of

oil.

• SHARP BLADE

WARNING: Sharp blade on cutting attachment

shield. To prevent serious injury, do not touch the

line cutting blade.

• CHOKE CONTROL

1. • FULL choke position

2. • PARTIAL choke position

3. • RUN choke position

OIL AND FUEL INFORMATION

RECOMMENDED OIL TYPE

Using the proper type and weight of oil in the crankcase is

extremely important. Check the oil before each use and

change the oil regularly. Failure to use the correct oil, or using

dirty oil, can cause premature engine wear and failure.

Use a high-quality SAE 30 weight oil of API (American

Petroleum Institute) service class SF, SG, SH.

ADDING OIL TO CRANKCASE: INITIAL USE

NOTE: This unit is shipped without oil. In order to avoid

damage to the unit, put oil in the crankcase before you

attempt to start the unit.

Your unit is supplied with one 3.04

fluid oz. (90 ml.) bottle of SAE 30

SF, SG, SH oil (Fig. 1).

NOTE: Save the bottle of oil. It

can be used to measure the

correct amount during future

oil changes. See Changing

the Oil.

1. Unscrew the top of the bottle of oil and remove the paper

WARNING: OVERFILLING OIL CRANKCASE MAY

CAUSE SERIOUS PERSONAL INJURY. Check and

maintain the proper oil level in the crank case; it is

important and cannot be overemphasized. Check the

oil before each use and change it as needed. See

Changing the Oil.

Fig. 1

Funnel

Spout

seal covering the

opening. Replace the

top. Next, cut the tip off

the funnel spout (Fig. 1).

2. Place the unit on a flat

level surface (Fig. 2).

3. Remove the dipstick from

the crankcase (Fig. 3).

4. Pour the entire bottle

of oil into the oil fill

hole (Fig. 3).

NOTE: Never add oil to

the fuel or fuel tank.

5. Wipe up any oil that

may have spilled and

reinstall the oil fill plug/

dipstick.

Check oil before each use and change as needed. Refer to

Checking the Oil Level.

RECOMMENDED FUEL TYPE

Old fuel is the primary reason for improper unit performance.

Be sure to use fresh, clean, unleaded gasoline.

NOTE: This is a four cycle engine. In order to avoid damage to

the unit, do not mix oil with gasoline.

Fig. 2

Oil Fill

Oil Fill Plug/

Dipstick

Oil Fill Hole

Fig. 3

O-Ring

1 2 3 4 5 6 7 8 ... 55 56

Commentaires sur ces manuels

Pas de commentaire

Mtd Y26SS Manuel d'utilisateur Page 3

Commentaires sur ces manuels

Produits connexes et manuels pour Matériel de jardinage Mtd Y26SS