Mtd 615 Manuel d'utilisateur

SNOW THROWERModels 615, E6AE5, E645E, & E665FOPERATOR’S MANUALIMPORTANT: READ SAFETY RULES AND INSTRUCTIONS CAREFULLYMTD LLC, P.O. BOX 361131 CLEV

10Throttle ControlThe throttle control is located on the engine. It regulates the speed of the engine and will shut off the engine when pushed down co

11WARNING: The electric starter must beused with a properly grounded three-prongreceptacle at all times to avoid possibility ofelectric shock. Follow

12Check the adjustment of the auger control as follows:• When the auger control is released and in the disengaged “up” position, the cable should have

13Operating TipsNOTE: Allow the engine to warm up for a few minutesas the engine will not develop full power until it reachesoperating temperature.WAR

14Chute Assembly The distance snow is thrown can be adjusted by changing the angle of the chute assembly. To do so, stop the engine by removing the ig

15WARNING: When following instructions inseparate engine manual for draining oil, besure to protect frame to avoid oil dripping ontotransmission part

16IMPORTANT: NEVER replace the auger shear bolts with standard hex bolts. Any damage to the auger gearbox or other components as a result of doing so

17Drive Belt• Follow steps 1 through 4 of steps previous instructions.• Pull idler pulley up, and lift belt off engine pulley and friction wheel disc.

18SECTION 8: OFF-SEASON STORAGEWARNING: Never store the machine orfuel container indoors where there is an openflame, spark or pilot light such as o

19SECTION 10: PARTS LIST FOR MODEL SERIES 615, E6A5, E645 & E665 21246710914118161315513317Ref.No.PartNo. Description1. 618-0123 Housing—R.H.618-

2TABLE OF CONTENTSContent...PageImportant Sa

20Model Series 615, E6A5, E645 & E66512345678910111214151399181920212223242523222618272829303031931933918353637383941404243403945344617484744

21Model Series 615, E6A5, E645 & E665Ref. No.PartNo.Description1. 712-0116 Lock Jam Nut 3/8-242. 756-0178 Flat Idler 3. 784-5632B Auger Idler Arm4

22Model Series E6A5E, E645E & E665E Ref.No.PartNo. Description1. 710-1652 Hex Washer Screw 1/4-20 x .502. 731-1324 Belt Cover3. 732-0710 Extension

23Model Series 6151234567489101112131415161718192016212223242526Ref. No.Part No.Description1. 710-1652 Hex Washer Screw 1/4-20 x.52. 731-1324 Belt Cov

24Models Series 615, E6A5E, E645E & E665E123345678151518202119231515242526272829303132333437364041424344391112143538511121713552456484651475010915

25Models Series 615, E6A5E, E645E & E665ERef.No.PartNo. Description1. 705-5234A Clutch Lever Assembly - RH2. 705-5233A Clutch Lever Assembly - LH3

26Models Series 615, E6A5E, E645E & E665E11234455616” Wheels13” or 15” Wheels477891010111112151314151617181192021222324252526282942113031323334835

27Models Series 615, E6A5E, E645E & E665ERef. No.Part No. Description1. 710-1652 Hex Screw 2. 784-5688 Drive Cable Guide Bracket3. 784-5687A Auger

MANUFACTURER’S LIMITED WARRANTY FOR:The limited warranty set forth below is given by MTD LLC with respect to new merchandise purchased and used in the

3SECTION 1: IMPORTANT SAFE OPERATION PRACTICESThis symbol points out important safety instructions, which if not followed, could endanger the persona

44. Never operate with a missing or damaged discharge chute. Keep all safety devices in place and working.5. Never run an engine indoors or in a poorl

5Contents Of Hardware PackLay out the hardware according to the illustration below for identification purposes. Part numbers are shown in parentheses.

6SECTION 2: ASSEMBLING YOUR SNOW THROWERLoose Parts Figure 1 shows parts of the snow thrower packed loose in the carton. You will need these parts al

7• Insert the shift lever assembly through slot in the speed selector plate leaving the hex bolts on the shift lever assembly loose, but not removed.

8IMPORTANT: If the right hand lock-out cable is not adjusted correctly, the wheels will tend to turn. If the left hand lock-out cable is not adjusted

9• Adjust the chute directional control bracket so that the spiral on the chute directional control fully engages the teeth on the chute assembly. Tig