Mtd YM26BC Manuel d'utilisateur Page 10
- Page / 96
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
10
SECTION 3: ASSEMBLY INSTRUCTIONS
Pilot Step
Remove the Cutting Blade & Install the
Cutting Attachment
Remove the Cutting Blade
1. Align the shaft bushing hole with the locking rod slot and
insert the locking rod into the bushing hole. See Figure 8
.
2. Hold the locking rod in place by grasping it next to
the boom of the unit. See Figure 14.
3. While holding the locking rod, loosen the nut on the
blade by turning it clockwise with a 5/8 inch closed-
end or socket wrench. See Figure 14.
9. Remove the locking rod from the locking rod slot.
1/4-1/2 turn
Counterclockwise
6. Align the shaft bushing hole with the locking rod
slot and insert the locking rod into the bushing hole.
See Figure 8.
7. Put the blade retainer and nut on the output shaft.
Make sure that the blade is installed correctly.
8. Tighten nut counterclockwise against the blade while
holding the locking rod:
• If using a torque wrench and an 5/8 inch socket tighten
to: 325 - 335 in•lb, 27 - 28 ft.•lb, 37 - 38 N•m.
• Without a torque wrench, use a 5/8 inch closed-end or
socket wrench, turning the nut until the blade retainer is
snug against the shaft bushing. Make sure that the blade
is installed correctly, then rotate the nut an additional 1/4
to 1/2 turn counterclockwise. See Figure 13.
Cutting Attachment
Locking Rod
Clockwise
6. Remove the locking rod.
7. Install the cutting attachment shield. Refer to Remove
and Install the Cutting Attachment Shield.
Blade Retainer
Output Shaft
Bushing
5. Make sure that the cutting blade is centered on the
pilot step and sitting flat against the output shaft
bushing. See Figure 12.
4. Remove the nut, blade retainer and blade. Store the
nut and blade together for future use in a secure
place. Store out of children’s reach.
Install the Cutting Attachment
5.
Align the shaft bushing hole with the locking rod slot and
insert the locking rod into the shaft bushing hole.
See
Figure 8.
Place the blade retainer on the output shaft
with the flat surface against the output shaft bushing.
See
Figure 15.
Screw the cutting attachment
counterclockwise onto the output shaft. Tighten securely.
NOTE: The blade retainer must be installed on the output
shaft in the position shown for the cutting
attachment to work correctly.
WARNING:
To avoid serious personal
injury or damage to the unit, do not start or
operate this unit with the locking rod in the
locking rod slot.
WARNING: Do not sharpen the cutting blade.
Sharpening the blade can cause the blade tip
to break off while in use. This can result in
severe personal injury. Replace the blade.
WARNING: If the cutting blade is off-
center, the unit will vibrate and the blade
may fly off, causing possible serious
personal injury.
WARNING: To avoid serious personal
injury, the cutting head guard MUST be in
place at all times while operating the unit
as a trimmer.
WARNING: To avoid serious personal
injury, always wear gloves while handling or
installing the blade.
Figure 14
Figure 15
Figure 12
Figure 13
- Operator’s Manual 1
- While Operating 4
- Other Safety Warnings 5
- SECTION 2: KNOW YOUR UNIT 7
- Install the Harness 8
- Remove the Cutting Attachment 9
- Install the Cutting Blade 9
- Cutting Attachment 10
- Recommended Oil Type 11
- Fueling The Unit 12
- Recommended Fuel Type 12
- Starting Instructions 13
- Stopping Instructions 13
- CAUTION: 14
- Holding the Trimmer 15
- Decorative Trimming 16
- Using the Cutting Blade 16
- Maintenance Schedule 17
- Line Installation 17
- Single Line Installation 18
- SplitLine™ Installation 18
- Checking The Oil Level 19
- Installing a Prewound Reel 19
- Changing The Oil 20
- Air Filter Maintenance 21
- Carburetor Adjustment 21
- Rocker Arm Clearance 22
- •lb (2.2–3.4 N•m) 23
- Replacing the Spark Plug 24
- Spark Arrestor Maintenance 24
- Accessories/Replacement Parts 25
- Transporting 25
- Cleaning 25
- Long Term Storage 25
- SECTION 9: SPECIFICATIONS 27
- P.O. Box 361131 30
- Cleveland, OH 44136-0019 30
- Manuel de l'utilisateur 31
- TABLE DES MATIÈRES 32
- TROUVER LE NUMÉRO DE MODÈLE 32
- SERVICE TECHNIQUE 32
- VISITEZ NOTRE SITE WEB 32
- LIRE TOUTES LES INSTRUCTIONS 33
- Avant L'utilisation 33
- Désherbeuses À Essence 34
- Aprés L'Utilisation 35
- APPLICATIONS 37
- INSTALLER LE HARNAIS 38
- D'ACCESSOIRE DE COUPE 38
- LA LAME DE COUPE 39
- L'ACCESSOIRE DE COUPE 40
- TYPE D'HUILE RECOMMANDÉ 41
- AVERTISSEMENT : 42
- INSTRUCTIONS DE DÉMARRAGE 43
- INSTRUCTIONS D'ARRÊT 43
- SECTION 6: MODE D’EMPLO 44
- PROGRAMME D'ENTRETIEN 47
- INSTALLATION DU FIL 47
- Pièces de rechange 49
- CHANGEMENT D'HUILE 50
- ENTRETIEN DU FILTRE À AIR 51
- Nettoyage du filtre à air 52
- Réglage du ralenti 52
- REMPLACEMENT DE LA BOUGIE 54
- ENTRETIEN DU PARE-ÉTINCELLES 54
- NETTOYAGE 55
- ENTREPOSAGE 55
- ENTREPOSAGE DE LONGUE DURÉE 55
- TRANSPORT 55
- SECTION 9: CARACTERISTIQUES 57
- REMARQUES 58
- Garantie du fabricant 59
- Manuel del Dueño/Operador 61
- PARACHISPAS 63
- ¡ADVERTENCIA! 63
- California 63
- ADVERTENCIA 63
- Durante la Operacion 64
- Despues del Uso 65
- APLICACIONES 67
- Instalación 68
- ACCESORIO DE CORTE 69
- INSTALACIÓN DEL ARNÉS 69
- TIPO DE ACEITE RECOMENDADO 72
- USO INICIAL 72
- INSTRUCCIONES DE ARRANQUE 74
- INSTRUCCIONES DE APAGADO 74
- COMO SOSTENER EL RECORTADOR 76
- RESULTADOS AL RECORTAR 76
- RECORTE DECORATIVO 77
- USO DE LA CUCHILLA DE CORTE 77
- PROGRAMA DE MANTENIMIENTO 78
- INSTALACION DE LA LINEA 78
- INSTALACIÓN DE UN CARRETE 80
- PREBOBINADO 80
- CAMBIO DEL ACEITE 81
- AJUSTE DEL CARBURADOR 82
- HUELGO DEL BRAZO OSCILANTE 83
- TRANSPORTE 86
- LIMPIEZA 86
- ALMACENAMIENTO 86
- ALMACENAMIENTO PROLONGADO 86
- SECCIÓN 9: ESPECIFICACIONES 88
- PARTS LIST 93
Produits connexes et manuels pour Matériel de jardinage Mtd YM26BC
(40 pages)
(72 pages)© 2020, manymanuals.fr. Tous droits réservés | 1.004 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels