Mtd YM90 Manuel d'utilisateur Page 8
- Page / 82
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
8
SECTION 3: ASSEMBLY INSTRUCTIONS
Installing and Adjusting the J-handle
1. Place the J-handle between the top and middle
clamp pieces. See Figure 1.
2. While holding the three pieces together, install the four
(4) screws through the top clamp and into middle clamp.
NOTE: The holes in the top and middle clamp will line up
only when assembled correctly.
3. Place the clamps and the J-handle over the shaft
housing and onto the bottom clamp.
4. Hold each hex nut in the bottom clamp recess with a
finger. Start screws with a large Phillips screwdriver.
Do not tighten until you make the handle adjustment.
5. Slide the J-handle in or out until the arrow/white line on the
decal touches the clamp assembly.
See Figure 2.
You
must first loosen the screws if the handle is pre-installed.
Figure 3
Figure 4
6. While holding the unit in the operating position,
arrange the J-handle to the location that provides you
the best grip. See Figure 3.
7. Tighten the clamp screws evenly, until the J-handle
is secure.
(4) Screws
Top Clamp
J-Handle
Middle Clamp
Bottom Clamp
Nuts
Decal
Figure 2
Figure 1
Support Fitting
Remove and Install the Cutting Attachment
Shield
Remove the cutting attachment shield when using the
unit as a brushcutter
Remove the cutting attachment shield from the shield
mount by removing the three (3) screws with a flat blade
screwdriver. See Figure 7. Store parts for future use.
Install the Harness
1. Push the strap through the center of the buckle.
2. Pull the strap over the cross bar and down through
the slot in the buckle. See Figure 4.
3. Put the harness on over head and onto shoulder.
Snap it on to the support fitting. See Figure 5.
4. Adjust length to fit the operator’s size. Pull tab to
lengthen, pull strap to shorten. See Figure 6.
WARNING: Always use the shoulder
harness when using the cutting blade to
avoid serious personal injury.
Figure 6
WARNING: The cutting attachment shield
should NOT be installed when operating the
unit with a blade. Remove the cutting
attachment shield before removing or
installing the blade.
Figure 5
- Operator’s Manual 1
- While Operating 4
- Other Safety Warnings 5
- SECTION 2: KNOW YOUR UNIT 7
- Install the Harness 8
- Install the Cutting Blade 9
- Remove the Cutting Attachment 9
- Cutting Attachment 10
- Stopping Instructions 12
- Starting Instructions 12
- CAUTION: 13
- Holding the Trimmer 14
- Decorative Trimming 15
- Using the Cutting Blade 15
- Line Installation 16
- Maintenance Schedule 16
- Single Line Installation 17
- SplitLine™ Installation 17
- Air Filter Maintenance 18
- Installing a Pre Wound Reel 18
- Replacement Parts 18
- Spark Arrestor Maintenance 19
- Replacing the Spark Plug 20
- Carburetor Adjustment 20
- Accessories/Replacement Parts 21
- Long Term Storage 21
- Cleaning 21
- Transporting 21
- SECTION 9: SPECIFICATIONS 23
- SECTION 9: NOTES 24
- P.O. Box 361131 26
- Cleveland, OH 44136-0019 26
- Manuel de l'utilisateur 27
- TABLE DES MATIÈRES 28
- TROUVER LE NUMÉRO DE MODÈLE 28
- SERVICE TECHNIQUE 28
- VISITEZ NOTRE SITE WEB 28
- LIRE TOUTES LES INSTRUCTIONS 29
- Avant L'utilisation 29
- Désherbeuses À Essence 30
- Aprés L'Utilisation 31
- APPLICATIONS 33
- INSTALLER LE HARNAIS 34
- D'ACCESSOIRE DE COUPE 34
- LA LAME DE COUPE 35
- L'ACCESSOIRE DE COUPE 36
- INSTRUCTIONS D'ARRÊT 38
- FONCTIONNEMENT DU EZ-Link 39
- TENUE DE LA DÉSHERBEUSE 40
- RÉGLAGE DE LA LONGUEUR DU FIL 40
- CONSEILS POUR BIEN DÉSHERBER 40
- COUPE DÉCORATIVE 41
- PROGRAMME D'ENTRETIEN 42
- INSTALLATION DU FIL 42
- Installation du fil simple 43
- Installation du SplitLine 43
- ENTRETIEN DU FILTRE À AIR 44
- ENTRETIEN DU PARE-ÉTINCELLES 45
- REMPLACEMENT DE LA BOUGIE 46
- RÉGLAGE DU CARBURATEUR 46
- NETTOYAGE 47
- ENTREPOSAGE 47
- ENTREPOSAGE DE LONGUE DURÉE 47
- TRANSPORT 47
- SECTION 9: CARACTERISTIQUES 49
- SECTION 9: REMARQUES 50
- Garantie du fabricant 51
- Manuel del Dueño/Operador 53
- PARACHISPAS 55
- ¡ADVERTENCIA! 55
- California 55
- ADVERTENCIA 55
- Durante la Operacion 56
- Despues del Uso 57
- APLICACIONES 59
- Instalación 60
- ACCESORIO DE CORTE 61
- INSTALACIÓN DEL ARNÉS 61
- COMBUSTIBLE 64
- INSTRUCCIONES DE APAGADO 65
- INSTRUCCIONES DE ARRANQUE 65
- COMO SOSTENER EL RECORTADOR 67
- RESULTADOS AL RECORTAR 67
- RECORTE DECORATIVO 68
- USO DE LA CUCHILLA DE CORTE 68
- PROGRAMA DE MANTENIMIENTO 69
- INSTALACIÓN DE UN CARRETE 71
- PREBOBINADO 71
- Limpieza del Filtro de Aire 71
- MANTENIMIENTO DEL PARACHISPAS 72
- AJUSTE DEL CARBURADOR 73
- LIMPIEZA 74
- ALMACENAMIENTO 74
- ALMACENAMIENTO PROLONGADO 74
- ACCESORIOS/PIEZAS DE REPUESTO 74
- TRANSPORTE 74
- SECCIÓN 9: ESPECIFICACIONES 76
- Item Part No. Description 80
- Part No. Description 80
- Optional Accessories 81
Produits connexes et manuels pour Matériel de jardinage Mtd YM90
(2 pages)
(64 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.661 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels